Q-See QC3016 Wartungshandbuch PDF herunterladen (Seite 23)

44 45

You cannot use Copy/Paste in Motion Detection because each channel will have a different

display. Right-clicking will exit the screen and your settings will be saved.

Sensitivity – The system supports six levels of sensitivity with Level 6 being the most

sensitive.

VIDEO LOSS

By default, this is enabled. In the event that the DVR detects a loss of signal from a camera,

it will send out a notiﬁcation or activate other functions based on your settings in the lower

portion of the Event window.

CAMERA MASKING

This is also enabled by default. If the system detects that something has covered a camera, it

will respond based on your settings in the lower portion of the window.

EVENT RESPONSE

The lower portion of the Event window determines what actions the DVR will initiate upon

detection of one of the three event types. Responses to a speciﬁc type of event can be

individually tailored to each camera, but the response to different types of events must be set

independently of each other. (ie: The response settings for a motion detection event do not

change the settings for a video loss event – even if you’ve set identical responses.)

PICTURE 3-23

PICTURE 3-24

Trigger Period - This is where you set the

schedule of when you want the DVR

to record motion events. It operates

in the same manner as the Schedule

menu as described in Section

3.6 with six blocks of time that can

be laid out for recording to occur

during a day. Not all blocks have to

be conﬁgured or enabled. You can

conﬁgure each day individually, or

you can make separate schedules for

week days and weekends.

Set

Sun

Mon

Tue

Wed

Thu

Fri

Sat

Mon

00 :00 -24 :00

Copy Paste Default Save Cancel

0 3 6 9 12 15 18 21 24

EVENTS

Event Type

Enable

Region

Period

Hold Time

sec.

Channel

Sensitivity

Motion Detect 1

Select

Set

Copy Paste Default Save Cancel

Rec. Continue sec.

Show Message Alarm upload Send Email

Record Channel

PTZ Activation

Tour

Snapshot

Buzzer

1 2 3 4

Select

The Set button will appear when either

Work Day or Free Day is selected in the

drop-down. This allows you to arrange the

schedule to reﬂect your business’ weekly

schedule.

PICTURE 3-25

Set

Sun Mon Tue Wed Thu Fri Sat

Work Day

Free Day

Save Cancel

The Copy and Paste buttons allow you to duplicate a day’s settings on another day while the

Default button returns the DVR to recording Motion Detection events 24/7.

Once you have made your settings, select OK to save them and you will be returned to the

Event menu. Hitting Cancel or right-clicking to exit the menu will not save your changes.

Hold Time – This is the length of time that the DVR will watch for another motion event before

treating a second event as a separate alarm. The delay can be from 0 to 600 seconds

(10 minutes).

Record Continue – The DVR will continue to record for a period after the event has ended.

This can be set to last up to 5 minutes.

Show Message – When this is enabled, the system will bring up the Alarm Status window

whenever an event is detected. You can conﬁgure this to display when motion, video

loss or masking is detected.

Alarm Upload – Your DVR can upload an alert message to the FTP server. Please see

Advanced Network Setup in Section 1.2 of the Remote Monitoring Guide

for instructions on setting up the DVR to work with an FTP server.

Send E-mail – E-mail notiﬁcations can be sent a single e-mail address. Please see

Advanced Network Setup in Section 1.2 of the Remote Monitoring Guide

for instructions on how to set up the e-mail alerts including recipient address.

Record Channel – When one camera detects an event, you can set the DVR to activate

recording on other cameras.

PTZ Activation – When selected, this will cause a connected Pan-Tilt-Zoom camera to

perform a pre-set action. This would be the ﬁrst action programmed for the camera in

the PTZ menu. Please see Chapter 5 for instructions on setting up a PTZ camera.

Tour – This will cause the DVR to cycle through selected channels on the display in live view.

Snapshot – The DVR is capable of taking still images which can be sent via e-mail or FTP

(See Advanced Network Setup in Section 1.2 of the Remote Monitoring

Guide for full instructions.)

Buzzer – When selected, the DVR’s internal alarm will sound when an event occurs.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 44 45

Kommentare zu diesen Handbüchern

Keine Kommentare

Q-See QC3016 Wartungshandbuch Seite 23

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Digitale Videorecorder (DVR) Q-See QC3016